The baler is also called the strapping machine. Here are some faults and troubleshooting methods that are easy to occur with the baler.
Condition 1: There is a lot of circumstances that can cause this situation:
1, the elastic adjustment is too tight
2, the sliding sheet or the slip belt has oil, which is located near the elastic adjustment, must be removed to wipe off the oil.
3. The belt is too tight, lower the belt drive seat down, or adjust the motor to the back.
4. Switch to a thinner belt or the belt pulley is too large.
Condition 1: The cassette processing, when the tape is stuck in the middle of the roller, or there is a foreign object plugged and cannot be taken out, the processing method is as follows:
5. Remove the washer of the hex nut.
6. Loosen the two M5 countersunk screws on the intermediate connecting shaft. Since the two screws are fixed to the notched part of the connecting shaft, the screws must be turned.
7. Remove the connecting shaft and lift the upper turbine to remove the jammed objects.
8, according to the above cba way to assemble and restore.
9. Note that the nut and L-shaped curved plate maintain a clearance of 0.3-0.5mm.
Condition 2: Poor adhesion:
1. The temperature is too high or not enough. Sometimes it is a special belt, the viscosity is poor, and the temperature must be accurate.
2, the use of voltage is not enough, there are many factories, the voltage is often insufficient, if you use the extension cable or cable, causing the pressure drop, the original adjustment of the temperature becomes lower, even when the motor is tied tightly burned, so try to avoid using the cable If you must use an extension cord, you must connect a thicker wire instead of a long cable.
3. The 635 bearing under the middle knife is broken, so there is heating and it is completely impossible to bond.
4. The long pull spring on the electric hot hand (swing bar) is tired, so it is impossible to pull the strange hand to the position, resulting in half or even less bonding.
5, the electric steel sheet is too high or too low, or left to the right, so hit the upper and lower PP belt, or the left and right tools, and can not enter the heating, subject to adjustment.
6. The micro fan of the exhaust smoke is faulty, making the temperature too high.
Condition 1: There is a lot of circumstances that can cause this situation:
1, the elastic adjustment is too tight
2, the sliding sheet or the slip belt has oil, which is located near the elastic adjustment, must be removed to wipe off the oil.
3. The belt is too tight, lower the belt drive seat down, or adjust the motor to the back.
4. Switch to a thinner belt or the belt pulley is too large.
Condition 1: The cassette processing, when the tape is stuck in the middle of the roller, or there is a foreign object plugged and cannot be taken out, the processing method is as follows:
5. Remove the washer of the hex nut.
6. Loosen the two M5 countersunk screws on the intermediate connecting shaft. Since the two screws are fixed to the notched part of the connecting shaft, the screws must be turned.
7. Remove the connecting shaft and lift the upper turbine to remove the jammed objects.
8, according to the above cba way to assemble and restore.
9. Note that the nut and L-shaped curved plate maintain a clearance of 0.3-0.5mm.
Condition 2: Poor adhesion:
1. The temperature is too high or not enough. Sometimes it is a special belt, the viscosity is poor, and the temperature must be accurate.
2, the use of voltage is not enough, there are many factories, the voltage is often insufficient, if you use the extension cable or cable, causing the pressure drop, the original adjustment of the temperature becomes lower, even when the motor is tied tightly burned, so try to avoid using the cable If you must use an extension cord, you must connect a thicker wire instead of a long cable.
3. The 635 bearing under the middle knife is broken, so there is heating and it is completely impossible to bond.
4. The long pull spring on the electric hot hand (swing bar) is tired, so it is impossible to pull the strange hand to the position, resulting in half or even less bonding.
5, the electric steel sheet is too high or too low, or left to the right, so hit the upper and lower PP belt, or the left and right tools, and can not enter the heating, subject to adjustment.
6. The micro fan of the exhaust smoke is faulty, making the temperature too high.
Frozen Seafood Mix,Mixed Seafood Bags,Frozen Seafood Mix Bags,Frozen Seafood Cocktail
Zhoushan Haiwang Seafood Co., Ltd. , https://www.haiwangseafoods.com